Editor in Chief: Prof. Govind R. Kadambi, PVC-Research

Archives list

Vol 07, Issue 1, April 2008

Sl. No. Contents
1

Modification of Driver Cabin Structure to Address Structural Failures using Experimental Modal Testing and Analysis
D.V. Balamurali Krishna, Vijaykumar S.M., Prashanth B.

2 Measurement and Analysis of a Can Chain Noise for Source Identification and Mitigation
Kumaraswamy S. Dr. B.V. Vijay, Vijay Kumar S. M.
3 Development and Implementation of Control Algorithm for Adaptive Front Light System of a Car
Shaji Alakkat, Sanosh Patel B.J., A.C.Meti
4 Development of Motion Tracking Based Running Exergame
Purushotham Rao Nikkam D., Harshal Sawant, Archana Patil
5 Rationalising of Warehouse Locations for Inventory Reduction of Bosch Power Tool Division
Varun V. Ajitkumar, Usha S.
6 Design of a Farm Tractor Focus on Utility and Ergonomics
Rathiskumar, Selvaraj, Prakash V. Unakal
7 Design of a Pram for Indian Babies, Emphasizing Usability and Aesthetics
Renju Varghese George, Manas Ranjan Mishra
8 Numerical Investigation of Spray Characteristics of a Swirl Airblast Atomizer for Varying Geometry and Flow Conditions
Jyotichandra Jingade, S.N.Sridhara
9 Effect of Foreign Object Damage on Fatigue Life of Compressor Blades in a Gas Turbine Engine
Janardhan P, N.C. Mahendra Babu.
10 Development of an Industry Standard QRS Detection Algorithm for Automated ECG Analysis
Saima Mohan, Govind R Kadambi, Viswanath K Reddy, M.D. Deshpande
11 Development of AC Induction Motor Control Software for X-Ray Tube
Manoj R, M. Arun Kumar, Srikanta Prasad
12 Design and FPGA/ASIC Implementation of Distorted Template based Time-of-Arrival Estimator for Local Positioning Application
Sanjana T.S., Selvakumar R., Cyril Prasanna Raj
13 Design and Implementation of Motion Estimation Technique for H.264 Advanced Video Coder on FPGA
A.C. Vikram, Selva Kumar, Shridhar Laddha

Vol 07, Issue 2, September 2008

Sl. No.Contents
1 Automotive Chassis Sizing Optimisation for Modal and Distortion Criteria
J.M. Biradar, B.V.Vijay, Kailash Jat
2 Numerical Simulation of Combustion Process in a DI Engine using Micro Chambers in Piston Head
Santosh J., S. N. Sridhara, Poovanna C.T.
3 Lead Time Reduction of Component Manufacturing Through Quick Changeover (QCO)
Bharath R., A C Lokesh
4 Design of Multifunctional Air Transportable Ground Support Trolley
Abhijeet Atwadkar, Sudheendra Kumar, Vineet Bhalla
5 Exterior Styling of Futuristic car that Reflects the Essence of Indian Design
Brijesh kumar VM, Prakash Unakal, Pankaj Jhunja
6 Numerical Studies on the Effect of Impeller Blade Skew on Centrifugal Compressor Performance
V.C. Arunachalam, Q.H. Nagpurwala, M.D. Deshpande, S.R. Shankapal
7 Design and Development of Terminals of Hand-Held GPS using LinSeed Chip
Ritika Singh, Govind R. Kadambi, Krishnamurthy V.
8 Design and Implementation of an Automobile Theft Deterrent System
Ajay D. Murthy, B.N. Shobha, Krishnamurthy Vaidyanathan
9 Handling Indeterminism – Key to better Software Project Management
H. Sarojadevi , MSRSAS, Bangalore
10 Design and Implementation of Digital Front End Module of MIMO-OFDM on FPGA
Syed Muneeb ur Rehman, Cyril Prasanna Raj P.
11 Analog VLSI Implementation of Novel Hybrid Neural Network Multiplier Architecture
Venkatesh S., Cyril Prasanna Raj P.

ISSN: 2249-5924